Slip resistant modified polysiloxane floor sealer
Improves coefficient of friction when properly applied
Superior ultra-violet weathering
Chemical and stain resistant
Low VOC – Low Odor
Clear and solid color finishes
Gloss and low semi-gloss
LEED NC 2009 compliant
Slip resistant coating system
Commercial and institutional floors
Industrial maintenance floors
Concrete flooring (interior/exterior)
Ceramic tile floors (interior/exterior)
Polished stone floors
|% SOLIDS by volume||92% as applied|
|COATINGS VOC (as packaged)||max. 3 g/l (less water & exempt compounds)|
|APPLIED VOC (reacted)||max. 89 g/l (less water & exempt compounds)|
|includes reaction volatiles|
|COMPONENTS||Advanced Polymer Modified Epoxy Coating|
|Resin 4 parts /Activator 1 part|
|POT LIFE||4 hours @ 70° F, 21° C|
|SHELF LIFE||one year (unopened)|
|FLASH POINT||109° F, 42.8° C|
|MIX RATIO||4:1 (4 parts resin : 1 part activator)|
|RECOMMENDED DRY FILM THICKNESS||3-5 mils per coat (75-125 microns), 1 to 2 coats|
|THEORETICAL COVERAGE||491 – 295 sq. ft. at recommended DFT (theoretical)|
Precision SlipShield 1000 slip resistant floor sealer may be applied over appropriately prepared concrete, ceramic tile, polished stone, wood flooring, tightly adherent coatings as well as steel and galvanized decking. Precision SlipShield 1000 is available in clear, Fleet White, Titanium Gray, Medium Gray, Dark Gray, Shadow Beige, Desert Brown, OSHA Safety Red, OSHA Safety Yellow and OSHA Safety Blue.
Flooring installation professionals are best equipped to install SlipShield 1000. An audit to determine the coefficient of friction of the finished floor is recommended.
Concrete – Surface must be cured, clean, dry and free of contamination. Water vapor pressure in concrete shall not exceed 4 lbs. per 1,000 square feet. Shot blast to remove laitance and achieve a 70-80 mesh profile appearance. Prime with Precision ST100 epoxy primer.
Ceramic Tile – Tile surface and grout must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on
ceramic tile to ensure adhesion prior to commencement of full application of Precision SlipShield 1000. Polished Stone Flooring – Stone surface and grout must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on polished stone to ensure adhesion prior to commencement of full application of Precision SlipShield 1000.
Hardwood Flooring – wood surface must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on wood flooring to ensure adhesion prior to commencement of full application of Precision SlipShield 1000.
Steel – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, SSPC-SP6 or SSPC-SP7. Substrate must be clean and dry prior to application of the ST100 surface tolerant primer. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used. New and Existing Coated Surfaces – Physically abrade existing coated surfaces thoroughly and completely with 180 grit or equivalent abrasive paper or scuff pad. . Substrate must be clean and dry prior to application of the Precision SlipShield 1000. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Stir or shake thoroughly to ensure uniform mixture. Mix 4 parts Modified Epoxy Coating with 1 part Epoxy Activator. Additional reduction is not necessary
Precision SlipShield 1000 is designed for application by professional coating applicators only. Precision SlipShield 1000 is commonly applied by floor coating application pad, roller or brush application on flooring. Please see Guidance for the Application and Maintenance of SlipShield 1000. Utilize a 3/16” or 3/8” nap phenolic core roller. Application can also be done by spray. Recommended film thickness is 3.0 to 7.0 mils DFT. Surface temperatures must be at least 5º F (3º C) above the dew point for application. Relative humidity below 40% will extend the dry times.
Roller – 3/16” to 3/8” inch nap, phenolic core
Brush – natural bristle
Floor Coating Applicator Pad – Lambskin
Dry times @ 70˚F (21˚C) and 50% RH
|Tack Free||4 hours|
|Dry Time||24 hours light traffic / 48 hours full traffic|
|Recoat||Clean surface and abrade with 180 grit abrasive paper prior to recoating,|
Follow local, state and federal regulations. Clean all spray equipment immediately after use. Acetone may be used to clean spray equipment. PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the Precision SlipShield 1000 system. Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin. Acetone may be used to clean application equipment immediately after use.
Precision SlipShield 1000 can be cleaned and maintained with water and mild non-abrasive detergent cleaning. In order to optimize and maintain its slip-resistant properties, Precision SlipShield 1000 should NOT be waxed.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.