Turns a smooth surface into a write & erase space with a dry erase marker
Available in white, clear, metallics & solid colors
Standard Sheen: Gloss
Surface ready for use in 5 days
LEED NC 2009 compliant
Two component modified epoxy coating Easily cleaned
Low VOC / Low Odor
Excellent chemical durability
Cures at ambient temperature
Interior / Exterior on appropriate substrates
Precision EeZeClean converts paintable surfaces including walls, columns, panels, hallways and old chalk boards into creative writing / art spaces.
Ideal for offices, schools, hospitals, retail, government and hospitality
|% SOLIDS by volume||92% as applied|
|COATINGS VOC (as packaged)||max. 3 g/l (less water & exempt compounds)|
|SPRAYABLE VOC (as applied)||max. 89 g/l (less water & exempt compounds)|
|includes cure volatiles|
|COMPONENTS||Advanced Polymer Modified Epoxy Coating|
|Resin 4 parts / Activator 1 part|
|POT LIFE||4 hours @ 70° F, 21° C|
|SHELF LIFE||one year (unopened)|
|FLASH POINT||109° F, 42.8° C|
|MIX RATIO||4:1 (4 parts resin : 1 part activator)|
|RECOMMENDED DRY FILM THICKNESS||3-5 mils per coat (75-125 microns), 1 to 2 coats|
|THERORETICAL COVERAGE||401 – 240 sq ft at recommended DFT (theoretical)|
Precision EeZeClean Dry Erase may be applied directly over property prepared substrates (Level 5 smoothness is recommended) including steel, aluminum, galvanizing, concrete, masonry, ceramic tile, MDF, drywall and previously primed or coated surfaces. Good painting practices dictate that before applying this Precision product, a test be performed to ensure that the adhesion, appearance, and color are compatible with the substrate and meet the expectations of the owner.
Steel, Aluminum & Galvanizing– Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or 7. Substrate must be clean and dry prior to application of the Precision EeZeClean Dry Erase. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Ceramic Tile – Tile surface and grout must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on ceramic tile to ensure adhesion prior to commencement of full application of Precision EeZeClean Dry Erase.
Concrete, Masonry, Interior MDF, Interior Drywall, FRP – Surface must be cured, clean, dry, and free of any dirt, dust, grease, oil, wax, mildew, disintegrated or chalky materials or other contaminants. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Previously Coated surfaces – Physically abrade existing coated surfaces thoroughly and completely with 220 grit or equivalent abrasive paper or scuff pad. . Substrate must be clean and dry prior to application of the Precision EeZeClean Dry Erase For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Use & Maintenance – Use any standard dry erase marker. For best results, use Expo® Bold or low odor dry erase markers. For daily erasing and cleaning, use a clean, dry erase cotton cloth, eraser, or micro-fiber towel. Periodically use a clean damp cloth, dry erase cleaner or isopropyl alcohol.
To optimize performance Precision Coatings recommends EeZeClean be applied over a smooth substrate such as a Level 5 wall finish. EeZeClean can be professionally sprayed to optimize finish smoothness. Stir or drill motor mix thoroughly to ensure uniform mixture. Mix 4 parts EeZeClean Dry Erase resin with 1 part EeZeClean Dry Erase activator. Additional reduction is not usually necessary, but if needed, use Precision’s 16060 VOC Exempt Reducer.
Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI maximum at the air cap for HVLP spray guns. Apply 1 -2 medium wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats. Recommended film thickness is 3.0 to 5.0 mils DFT. Surface temperatures must be at least 5º F (3º C) above the dew point for application.
|Type||Fluid Tip||Spraying Pressure|
|Siphon Feed||1.4mm –1.7mm||40-65-PSI|
|Gravity Feed||1.3mm – 1.4mm||40-65 PSI|
|HVLP Siphon||1.3mm – 1.5mm||max. 10 PSI @ the air cap|
|HVLP Gravity||1.3mm – 1.5mm||max. 10 PSI @ the air cap|
|Pressure Pot||1.1 mm- 1.3 mm||29 PSI – 58 PSI|
|Airless Spray||Double Orifice 312 through 512 Fine Finish Tips (for clears and solid colors only)|
Brush – natural bristle
Roller – ¼ to ½ inch nap, mohair or no-lint cover with a phenolic core
We do not recommend foam roller application
Dry times @ 70˚F (21˚C) and 50% RH
|Tack Free||4 hours|
|Dry Time||24 hours|
|Recoat||Full recoat 24 hours|
|Write On Time||Five Days|
PACKAGING Available in Quart and Gallon Kits
Follow local, state and federal regulations. Clean all spray equipment immediately after use. Acetone may be used to clean spray equipment. PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the Precision EeZeClean Dry Erase. Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin. Acetone may be used to clean application equipment immediately after use.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.